Associated Products
Wykamol EP40 Epoxy Floor Coating Primer Clear 5 Litre
Wykamol EP40 Epoxy Floor Coating Primer Clear is designed to soak into the substrate, block pores, improve adhesion and ensure an even, high quality finish.
Wykamol EP40 Epoxy Floor Coating Primer Clear 5 Litre
Wykamol No More Damp EP40 Epoxy Floor Coating Primer Clear is a water based floor coating. This easy to apply resin system has excellent adhesion with concrete and wood, providing attractive, hard wearing and dust-free finish. Floors become easier to clean and highly resistant to damage from fork-lift trucks, chemical, fuels and lubricants.
EP40 Primer is supplied in 2 tins - a base and a hardener - which are mixed together to form a complete product. No More Damp EP40 Epoxy Floor Coating is suitable for use in most industrial and domestic environments. It applies as a semi-gloss and dries with a semi-matt finish, depending on temperature and humidity.
To Download the Product Data Sheet (PDF) for Wykamol EP40 Epoxy Floor Coating Primer Click HERE
Coverage: 5 Litres will cover up to 40 m²
Colour: Clear
Size: 5 Litre
Wykamol EP40 Epoxy Floor Coating Primer Usage Instructions
SUBSTRATE PREPARATION
All substrates should be dry, clean and free from laitance, oil,grease and other contaminants. Ideally, concrete surfaces should be vacuum shotblasted or mechanically abraded (grinding) to both clean and open the suface, providing a good mechanical key.
Please note: Following sufficient substrate preparation, EP40 Epoxy Floor Primer should always be applied prior to the application of either the grey or clear finish coat.
Substrate humidity should be ≤ 80% before application commences. The concrete subbase must be ≥ 25 N/mm² as per BS 8204-6.
The subbase must be level and have no more than 2 mm undulations. If floor unevenness is significant a polymer modified C35 screed can be used to level. Contact the Wykamol Technical Department for more information.
MIXING
EP40 Epoxy Floor Primer and Finish Coat are both made by combining two components; part A and part B. The part A container is large enough to act as a mixing vessel when combining part A and part B.
By hand, thoroughly mix both part A and part B in their own vessels before combining. Add the entire contents of part B to the entire contents of the part A vessel and mix thoroughly.
Ideally, use a mechanical mixer under low shear to combine, ensuring minimal air entrapment. Do not allow mixture to sit for any considerable amount of time before applying, as it will begin to harden.
APPLICATION
EP40 Epoxy Floor Primer:
1. Using a stiff brush or roller, work the product into the substrate, ensuring all areas are completely covered.
2. Allow to cure for at least 12 hours prior to applying a EP40 Epoxy Finish Coat. If atmospheric or substrate temperatures are below 20°C, allow for a longer initial curing time. Product should be just tack free.
3. Do not allow Primer to fully cure - do not allow curing time to exceed 26 hours before applying a 2nd coat of Primer or Finish Coat.
Pot life 45 mins - 1.5 hours
Recoat time (cure at20°C)** 12 - 26 hours (or when just tack free)
Full chemical cure (at 20°C)** 7 - 14 days
Wykamol EP40 Epoxy Floor Coating Technical Information
Barcode: 5060207862387
Weight: 5.45kg
Storage: Store in original, sealed container between temperatures of 5°C and 20°C. Pot life once opened is approx. 45 mins -1.5 hours.
To Download the Safety Data Sheet (PDF) for Wykamol EP40 Epoxy Floor Coating Primer Part A Click HERE and for Part B Click HERE
Wykamol EP40 Epoxy Floor Coating Primer Clear 5 Litre
Wykamol No More Damp EP40 Epoxy Floor Coating Primer Clear is a water based floor coating. This easy to apply resin system has excellent adhesion with concrete and wood, providing attractive, hard wearing and dust-free finish. Floors become easier to clean and highly resistant to damage from fork-lift trucks, chemical, fuels and lubricants.
EP40 Primer is supplied in 2 tins - a base and a hardener - which are mixed together to form a complete product. No More Damp EP40 Epoxy Floor Coating is suitable for use in most industrial and domestic environments. It applies as a semi-gloss and dries with a semi-matt finish, depending on temperature and humidity.
To Download the Product Data Sheet (PDF) for Wykamol EP40 Epoxy Floor Coating Primer Click HERE
Coverage: 5 Litres will cover up to 40 m²
Colour: Clear
Size: 5 Litre
Wykamol EP40 Epoxy Floor Coating Primer Usage Instructions
SUBSTRATE PREPARATION
All substrates should be dry, clean and free from laitance, oil,grease and other contaminants. Ideally, concrete surfaces should be vacuum shotblasted or mechanically abraded (grinding) to both clean and open the suface, providing a good mechanical key.
Please note: Following sufficient substrate preparation, EP40 Epoxy Floor Primer should always be applied prior to the application of either the grey or clear finish coat.
Substrate humidity should be ≤ 80% before application commences. The concrete subbase must be ≥ 25 N/mm² as per BS 8204-6.
The subbase must be level and have no more than 2 mm undulations. If floor unevenness is significant a polymer modified C35 screed can be used to level. Contact the Wykamol Technical Department for more information.
MIXING
EP40 Epoxy Floor Primer and Finish Coat are both made by combining two components; part A and part B. The part A container is large enough to act as a mixing vessel when combining part A and part B.
By hand, thoroughly mix both part A and part B in their own vessels before combining. Add the entire contents of part B to the entire contents of the part A vessel and mix thoroughly.
Ideally, use a mechanical mixer under low shear to combine, ensuring minimal air entrapment. Do not allow mixture to sit for any considerable amount of time before applying, as it will begin to harden.
APPLICATION
EP40 Epoxy Floor Primer:
1. Using a stiff brush or roller, work the product into the substrate, ensuring all areas are completely covered.
2. Allow to cure for at least 12 hours prior to applying a EP40 Epoxy Finish Coat. If atmospheric or substrate temperatures are below 20°C, allow for a longer initial curing time. Product should be just tack free.
3. Do not allow Primer to fully cure - do not allow curing time to exceed 26 hours before applying a 2nd coat of Primer or Finish Coat.
Pot life 45 mins - 1.5 hours
Recoat time (cure at20°C)** 12 - 26 hours (or when just tack free)
Full chemical cure (at 20°C)** 7 - 14 days
Wykamol EP40 Epoxy Floor Coating Technical Information
Barcode: 5060207862387
Weight: 5.45kg
Storage: Store in original, sealed container between temperatures of 5°C and 20°C. Pot life once opened is approx. 45 mins -1.5 hours.
To Download the Safety Data Sheet (PDF) for Wykamol EP40 Epoxy Floor Coating Primer Part A Click HERE and for Part B Click HERE
Associated Products