Rustins Quick Dry Floor Varnish Satin 2.5 Litre

Rustins Quick Drying Floor Varnish Satin is a water-based, self-crosslinking (stronger), low odour floor coating that dries to a hard-wearing, durable and transparent finish.Non-toxic, quick drying, completely clear and non-yellowing. Rustins Floor Varnish Satin is resistant to water, alcohol, white spirit and similar solvents. Very hard wearing. Touch dry in 20 minutes and re-coatable in 2 hours.

Type: Water-based self-crosslink acrylic emulsion. The varnish looks milky-white whilst liquid but dries to a hard, durable transparent finish, resistant to alcohol and water.
Intended Use: Bare wood, hardboard, MDF, unsealed cork, concrete, stone, unsealed quarry and terracotta tiles. Interior use only.
Special Features: Low odour. Non-yellowing on ageing. Quick-drying. Wash brushes in water. Generally, has very little effect on the colour of the timber it is applied to.

Coverage: 10-12m² per Litre per coat, depending on the absorbency of the surface.

To Download the Product Information Sheet (PDF) for Rustins Floor Varnish Satin Click HERE

Finish:Satin
Also Available: Rustins Quick Dry Floor Varnish Gloss

Size: 2.5 Litre
Also Available: Rustins Quick Dry Floor Varnish Satin 1 Litre and Rustins Quick Dry Floor Varnish Satin 5 Litre

Rustins Quick Dry Floor Varnish Satin Usage Instructions

Preparation: The surface must be clean, smooth, dry and free from wax, dust and contaminants. Read the full instructions on the tin. Nail holes and small cracks may be filled with Rustin’s Wood Filler. Bare wood may be dyed before coating with Rustin’s Wood Dye. Other brands of dye, stain or paints may be incompatible. Do not apply Knotting or Sanding Sealer.
Application: Using a synthetic brush or varnish roller, apply evenly and liberally, finishing in the direction of the grain. When applying to power floated concrete or dense surfaces such as stone, dilute the first coat 1:1 with water.
Coats: Apply 3 liberal coats according to the coverage rate. More absorbent surfaces or commercial premises may require 4 coats. Important: If there is any grain raising after the 1st coat has dried, lightly sand the surface smooth before applying the next coat. Drying Time: Touch dry within 20 minutes depending on the temperature and humidity. Re-coating Time: 2 hours, depending on the temperature and humidity.
Application Temp: Ideally 15-25°C. Do not use below 10°C, or in conditions of high humidity.
Maintenance: The coating will accept light foot traffic 2 hours after the final coat, and will take 3 days to fully harden. During this period it should be protected from heavy wear and spills. Afterwards the surface may be kept clean by mopping with a mild detergent solution. To restore the gloss use Rustins Multi-Purpose Floor Shine. Worn areas may be recoated once cleaned and sanded to provide a key, it is not necessary to recoat the whole floor.
Compatibility: The coating may be used over the following Rustins products. Wood Filler, Wood Dye, Floor Dye and wood may be bleached before coating with Rustins Wood Bleach.
Important: If any other products are used, such as timber treatments or other brands of dye, stain or paints, these must be tested first for compatibility. Settlement: Stir well before and during use. Satin finishes may dry glossy if not stirred or the Varnish Stains will not dry to the correct colour
Clean-Up: With water whilst still wet. If dried-on, clean equipment and brushes with either Rustins Brush Restorer or Rustins Strypit.

Rustins Quick Dry Floor Varnish Satin Technical Information

Barcode : 5015332000050
Weight : 2.56kg

Shelf-life/Storage: Many years if stored in original, tightly closed container in normal conditions. Protect from frost. 
Hazards: Non-flammable. Flash point: Nil. General good practice advice: avoid contact with eyes, skin and clothing. 

To Download the Safety Data Sheet (PDF) for Rustins Quick Dry Floor Varnish Satin Click HERE