Thompsons Wet Look Patio and Block Paving Sealer 5 Litre

Thompsons Wet Look Patio and Block Paving Seal has been developed to not only enhance, stabilise and protect paving, but to provide it with a long-term solution to maintaining its appearance. The advanced acrylic formula not only enhances the appearance by highlighting its subtle variations it also provides it with long lasting protection. It is designed to protect against wear and tear and repel dirt to keep the surface looking cleaner for longer. The formula is chemical resistant to protect against oil and fuel spills and also contains a biocide to resist the moss, mould and lichen growth that can damage the coating and ruin the appearance.

This unique product is ideal for enhancing the appearance of newly laid paving or refreshing the look of older paving. Thompson's Patio and Block Paving Seal can be applied to block paving and flagstones including granite, cast and limestone.

Coverage: Thompson's Patio and Block Paving Seal will cover approximately 6m² per litre per coat. Coverage will depend on the texture and porosity of the surface to be coated.
As a guideline, Block Paving requires 6m² per litre per coat for the first application and 8m² per litre per coat for the second application.
Patio Slabs require 6.5m² per litres per coat for the first application and 8.5m² per litre per coat for the second application.

Finish: Wet Look
Also Available: Thompsons Natural Patio and Block Paving Sealer 5 Litre

Size: 4 x 5 Litre
Also Available Individually: See: Thompsons Wet Look Patio and Block Paving Sealer 5 Litre

Thompsons Wet Look Patio and Block Paving Sealer Usage Instructions

Usage Areas: Thompson's Patio and Block Paving Seal can be applied to block paving and flag stones including granite, cast and limestone. 
NOTE: Some block paving may discolour or darken and a clear seal such as Thompson's Patio and Block Paving Seal will highlight this effect. Blockpaving with a high lime content and newly laid blocks may produce unsightly white surface deposits which may reduce with weathering. Test on a small, inconspicuous area prior to general application. Avoid contact with plastic and rubber materials (including footwear) whilst wet.

Preparation:
New Block and Paving Slabs: Blocks or paving slabs and jointing sand should be dry. In order to avoid dislodging the jointing sand, the sand should be well compacted and slightly below the level of the block or paving slab. (Also see note regarding white deposits above) 
Existing Block Paving and Paving Slabs: Ensure all surfaces are clean, dry and free fom grease, oil, dust or loose material that may interfere with the penetration of the sealer to be applied. Dirt, moss, lichen and other loose material can be removed by using Thompson's Patio and Paving Cleaner. Grease and oil stains can be removed by using Everbuild Oil Away Spray. Rinse thoroughly with water to ensure all cleaning residues are washed away. Brush area to be coated to remove all surface debris. Allow to dry thoroughly.

Application: Shake well before use. For best results use a long pile roller and a roller tray or brush. Surfaces should be dry. Apply an even coat to ensure all surface irregularities are covered. Attention should be paid to textured block paving slabs to ensure the surface is evenly coated and that the coating does not 'pond' in surface depressions. Brush well into the surface redistributing any surplus material. Apply 2 coats allowing 4 hours between coats. Extremely porous surfaces may require a further coat. Do not apply when rain appears likely before the material has dried.
Drying Time: The surface will be touch dry in approximately 1 hour. Light traffic is acceptable after 4 hours. However, Thompson's Patio and Block Paving Seal does not reach it's optimum performance until after a few days and should be left overnight before vehicles can be parked on treated blocks or before subjecting the area to heavy use. In cold, damp conditions drying and recoating times will be extended.
Clean Up: Remove as much product as possible from application equipment before cleaning. Clean brushes, rollers and other equipment immediately after use with white spirit or brush cleaner. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses.
Wise Precautions:
1. Dries to a glossy, wet look finish, the level of the sheen will be dependent on the type and nature of the concrete. Colour and appearance of block paving can change significantly with the applications of Thompson's Patio and Block Paving Seal. Always test on an inconspicuous but representative area prior to coating the whole area.
2. Avoid spillage onto surrounding vegetation and protect adjacent areas such as decorative coatings and plastic. Remove splashes whilst still wet with a brush cleaner.

Thompsons Wet Look Patio and Block Paving Sealer Technical Information

Barcode: 5010214863129
Weight: 21.45kg

To Download the Safety Data Sheet (PDF) for Thompsons Wet Look Patio and Block Paving Sealer Click HERE