![image](/images/products/small/BON18104-210730034945-1.jpg)
Associated Products
Bonda Woodfill Teak 500g
Bonda Woodfill Teak is a superior two component rapid hardening wood filler used fill knots in timber, pin holes, defects etc.
Bonda Woodfill Teak 500g
Bonda Woodfill Teak is an superior two component rapid hardening wood filler. Easy to mix and apply and is used to fill knots in timber, pin holes, defects etc. It sands well to give a excellent base for finishing.
Type: A two-part polyester filler.
Intended Use: Easy to mix and apply and is used fill knots in timber, pin holes, defects etc. Easy to sand and tack free.
To Download the Product Data Sheet (PDF) for Bond Woodfill Click HERE
Colour: Teak
To See the Full Range of Bonda Woodfill Click HERE
Size: 500g
Also Available in a 1.5kg See: Bonda Woodfill Teak 1.5kg
Bonda Woodfill Teak Usage Instructions
Preparation: Should be applied onto a clean and dry substrate.
Application: Mix the filler with the hardener on a non-porous surface using an amount of filler the size of a golf ball to a pea-sized ball of hardener as the mixing ratio. Mix thoroughly until an even colour is obtained. Do not prepare more than is required as any excess will be unusable after 10 mins.
Curing Time: 30 mins – 1 hr depending on temperature and humidity.
Application Temp: Ideally 15-25°C, but do not use below 10°C.
Clean-Up: All tools must be cleaned immediately after use with Rustins Cellulose Thinners before product sets hard.
Bonda Woodfill Teak Technical Information
Barcode: 5014197181041
Weight: 0.61kg
Shelf-life/Storage: 18 months if stored under the recommended conditions. Store in cool and dry place below 25°C.
Hazards: Harmful by inhalation. Contains Styrene. Do not breathe vapours. Wear suitable protective gloves and eye/face protection.
To download the product safety data sheet (PDF) for Bonda Woodfill Click HERE
Bonda Woodfill Teak 500g
Bonda Woodfill Teak is an superior two component rapid hardening wood filler. Easy to mix and apply and is used to fill knots in timber, pin holes, defects etc. It sands well to give a excellent base for finishing.
Type: A two-part polyester filler.
Intended Use: Easy to mix and apply and is used fill knots in timber, pin holes, defects etc. Easy to sand and tack free.
To Download the Product Data Sheet (PDF) for Bond Woodfill Click HERE
Colour: Teak
To See the Full Range of Bonda Woodfill Click HERE
Size: 500g
Also Available in a 1.5kg See: Bonda Woodfill Teak 1.5kg
Bonda Woodfill Teak Usage Instructions
Preparation: Should be applied onto a clean and dry substrate.
Application: Mix the filler with the hardener on a non-porous surface using an amount of filler the size of a golf ball to a pea-sized ball of hardener as the mixing ratio. Mix thoroughly until an even colour is obtained. Do not prepare more than is required as any excess will be unusable after 10 mins.
Curing Time: 30 mins – 1 hr depending on temperature and humidity.
Application Temp: Ideally 15-25°C, but do not use below 10°C.
Clean-Up: All tools must be cleaned immediately after use with Rustins Cellulose Thinners before product sets hard.
Bonda Woodfill Teak Technical Information
Barcode: 5014197181041
Weight: 0.61kg
Shelf-life/Storage: 18 months if stored under the recommended conditions. Store in cool and dry place below 25°C.
Hazards: Harmful by inhalation. Contains Styrene. Do not breathe vapours. Wear suitable protective gloves and eye/face protection.
To download the product safety data sheet (PDF) for Bonda Woodfill Click HERE