Rustins Quick Dry Varnish Gloss Clear 2.5 Litre

Rustins Quick Dry Varnish Gloss Clear is a quick-drying, hard wearing coating for all interior woodwork. A tough and durable finish for all woodwork and cork. Apply 2-3 coats for the perfect finish. Low odour non-toxic and touch dry in 20 minutes, re-coatable in 2 hours. Can also be used as a sealer for concrete, brickwork and plaster.

Type: Water-based self-crosslinking acrylic emulsion. The varnish looks milky-white whilst liquid but dries to a hard, durable transparent finish, resistant to water and alcohol.
Intended Use: Interior, bare woodwork, cork, hardboard. Can also be used as a sealer for concrete, brickwork and plaster. For floors use Rustin’s Acrylic Floor Varnish.
Special Features: Low odour, quick-drying, non-yellowing on ageing. Wash brushes in water. Has very little effect on the colour of wood to which it is applied. Conforms to Safety of Toys Regulations BS EN 71 Part 3 1995.
Coverage: 12-15m² per Litre per coat, depending on absorbency of surface.

Finish: Gloss 
Also available in Matt and Satin

Size: 2.5 Litre

Also available in Rustins Quick Dry Varnish Gloss Clear 250ml, Rustins Quick Dry Varnish Gloss Clear 500ml, Rustins Varnish Gloss Clear 1 Litre and Rustins Varnish Gloss Clear 5 Litre

To Download the Product Information Sheet (PDF) for Rustins Quick Dry Varnish Gloss Clear Click HERE

Rustins Quick Dry Varnish Gloss Clear Usage Instructions

Preparation: Surfaces must be clean and previous coatings should be removed. It is advisable to clean old surfaces with White Spirit to remove any wax or contamination, wipe away the solution formed with clean kitchen paper towels. Bare wood may be dyed with either Rustins Wood Dye before varnishing.
Compatibility: Can be applied over either Rustins Wood Dye, other brands may be incompatible. Bare wood may be bleached with Rustins Wood Bleach prior to varnishing. Not for use over scumbles or oil-based paints. Other types of coatings/stains may be incompatible, including acrylic paints and vinyl emulsion. If using anything other than Rustins Wood Dye, a test area should be coated to determine compatibility.
Application: Synthetic brush, Varnish Roller or Spray (can be diluted with water about 10% if necessary for spraying, or if the temperature is high).
Coats: 2 or 3. Lightly sand after 1st coat to flatten any raised grain.
Drying Time: Touch dry in 20 minutes typically, depending on temperature and humidity.
Re-coating Time: Re-coat after 2 hours
Application Temp: Ideally 15-25°C, do not use below 10°C or in conditions of high humidity.
Maintenance: The varnish will take 3 days to fully harden. Spills should be wiped-up immediately during this time to prevent damage. The surface can be cleaned as required with a mild detergent solution, do not use aggressive cleaning products. Re-coat the varnish as necessary, after cleaning and lightly sanding the surface.
Clean-Up: With water whilst wet. If dried-on, clean equipment and brushes with either Rustins Brush Restorer or Rustins Strypit Paint and Varnish Stripper.

Rustins Quick Dry Varnish Gloss Clear Technical Information

Barcode: 5015332000104
Weight: 2.56kg

Shelf-life/Storage: Many years if stored in normal conditions. Protect from frost.
Hazards: Non-flammable. Flash point: Nil. General good practice advice: avoid contact with eyes, skin and clothing.

To Download the Safety Data Sheet (PDF) for Rustins Quick Dry Varnish Gloss Clear Click HERE